BACK TO PRODUCTS

Onshore Oil and Gas

Reliable Coating Solutions for Long-Lasting Performance
  • Extend service life with durable coatings.
  • Reduce unplanned shutdowns with corrosion protection.
  • Optimize efficiency in tough onshore environments.
     

EXPLORE CASE STUDIES

CASES

Durable Protection for a Landmark LNG Project

Filter by

Products

355 Product Found
My Filters
    Primer-Finish
    Interbuild 1073
    Interbuild 1073 is a two component, high solids content epoxy primer typically used in maintenance environments due to excellent surface tolerance properties. With a low VOC content, the primer can also be applied within internal environments and complies with the Indoor air quality standard as stipulated by EPA Method 24.
    Surface Tolerant
    Bar-Rust 236
    Bar-Rust 236 is a high performance, multi-purpose, surface tolerant, two-component chemically-cured epoxy semi-gloss coating.
    Preconstruction Primer
    Interplate 997
    A two pack, heat resistant zinc silicate shop (pre-construction) primer providing good corrosion protection (even after heating up to 800°C (1472°F)), with minimum production of zinc salts. Suitable for high speed welding and cutting with excellent resistance to damage caused by welding, gas cutting and fairing thereby reducing secondary surface preparation requirements in comparison to typical zinc silicate products.
    Primer
    Interprime 1068
    Interprime 1068 is an air drying Zinc Phosphate Primer designed for application to all types of steel surfaces. This primer is characterised by good anti-corrosive properties, easy application and the ability to protect hand cleaned steel. Interprime 1068 is primarily intended as a single coat system for use in mildly corrosive environments, classified in ISO12944-2 as up to and including C2.
    Surface Pre-Treatment
    Devstrip 501
    A cost effective, pH neutral paint remover for the removal of old paint and coatings systems from steel, concrete, aluminium and other alloys, wood and masonry substrates. *Please note this product is only available in North America.
    Chemical Resistant Lining
    Devran 124
    100% solids novolac epoxy coating with excellent chemical resistance properties which may be applied on both vertical and horizontal surfaces. *Please note this product is only available in North America.
    Primer
    Devran 201H
    A high performance, chemically cured, rust inhibitive epoxy primer for interior or exterior steel, galvanized metal or aluminium surfaces. *Please note this product is only available in North America.
    Primer-Finish
    Devtar 5A-HS
    A high performance, two-component, coal-tar free, chemically-cured high-build epoxy coating. *Please note this product is only available in North America.
    Preconstruction Primer
    Interplate 408
    A two component iron oxide epoxy shop primer. Approved for welding by Newcastle Primary Care Trust (NOHA). Approved for welding by Lloyd's Register.
    Finish
    Interfine 2700
    Direct-to-Metal epoxy polysiloxane finish
    Finish
    Devlac 1431
    A single component alkyd gloss enamel finish. *Please note this product is only available in North America.
    Filler
    Devmat 142HB
    A two component, 100% solids, solvent free epoxy caulking compound. *Please note this product is only available in North America.
    Primer-Finish
    Devthane 389N
    A high performance, two-component chemically-cured aliphatic urethane gloss finish. *Please note this product is only available in North America.
    Primer
    Devprime 1401
    A rust inhibitive primer for use over properly prepared steel. A general purpose shop primer, Devprime 1401 offers low cost, easy application and low VOC. *Please note this product is only available in North America.
    Temporary Protection
    RELEST Wind ProcessCoat - I373-2050
    RELEST Wind ProcessCoat is a Solvent-free translucent 2K polyurethane for use as an in-mold gelcoat with low film thicknesses. Utilizing the new generation of UV absorbers allows for temporary outdoor storage of uncoated rotor blades, without the risk of UV light damaging the substrate. The product's great sandability facilitates the further treatment of demoulded rotor blades and forms an excellent, pore-free basis for subsequent coatings.
    1. 1

    Sorry, we couldn't find any results
    Fetching the data, please wait...