BACK TO PRODUCTS

Wind Power

Comprehensive Coating Solutions for Renewable Energy
  • Protect wind turbines from harsh environments.
  • Extend component lifespan from tip to toe.
  • Ensure compliance with industry standards.
     

EXPLORE CASE STUDIES

CASES

Protecting the World's Largest Offshore Wind Farm

Filter by

Products

187 Product Found
My Filters
    Primer
    Devran 201H
    A high performance, chemically cured, rust inhibitive epoxy primer for interior or exterior steel, galvanized metal or aluminium surfaces. *Please note this product is only available in North America.
    Preconstruction Primer
    Interplate 408
    A two component iron oxide epoxy shop primer. Approved for welding by Newcastle Primary Care Trust (NOHA). Approved for welding by Lloyd's Register.
    Finish
    Interfine 2700
    Direct-to-Metal epoxy polysiloxane finish
    Finish
    Devlac 1431
    A single component alkyd gloss enamel finish. *Please note this product is only available in North America.
    Other
    Interdur 1130
    Interdur 1130 is an easy to use primer and finish in one. The product is well suited to a variety of uses including: internal steelwork where a good appearance is desired, external steelwork in low and moderate corrosion environments, OEM such as pre-engineered buildings (PEB). As a single component product, Interdur 1130 is a simple solution for the maintenance of existing structures.
    Other
    RELEST Wind Gelcoat - I372-7338
    RELEST Wind Gelcoat ca. RAL 7038, RA is a solvent free 2k viscoplastic, polyaspartic coating with excellent abrasion resistance. Suitable as part of a coating system for UV- and weather- resistance. Film thicknesses of approximately 200μm can be achieved in one step with optimal flow properties. RELEST Wind Gelcoat ca. RAL 7038, RA is characterised by its great adhesion to epoxy laminate.
    Filler
    RELEST Wind Putty Contour Cartridge - I373-3715
    RELEST Wind Putty Contour Cartridge is a Solvent-free, highly viscous polyurethane putty for smoothing surface and contour irregularities. Its easy sanding and rapid cure properties offers increased productivity for further processing and recoating. RELEST Wind Putty Contour is ideally situated for mechanical application. It is supplied in a convenient 2-component cartridge for direct application of minimal quantities without weighing.
    Primer-Finish
    Interdur 8844
    A low VOC, two component high build, high solids, epoxy immersion coating. Designed to give long term protection in a single coat for immersion service situations. A winter curing agent is available to assist faster turn around times in cold conditions. CHINA ONLY
    Other
    RELEST Wind LEP ETU - I374-8735
    RELEST Wind LEP Easy To Use is a two-component solvent-free polyurethane coating for the M&R market which is especially designed for protecting the leading edge of rotor blades of wind energy plants from erosion damage caused by rain, sand, hail, dirt and other particles suspended in the air. The coating consists of an exceptionally fast, hard wearing, UV- and abrasion resistant polyurethane elastomer.
    Surface Pre-Treatment
    Devprep 88
    A concentrated water based cleaner low in odour, non-flammable and biodegradable. *Please note this product is only available in North America.
    Primer-Finish
    RELEST Wind Adhesion Promoter - I367-0080
    RELEST Wind Adhesion Promoter is a two component polyurethane material designed to ensure optimal adhesion for PVC, aluminium cast, CDC, PMAA and GRP based on epoxy or polyester. It is is especially suited for use in combination with wear protection coatings for rotor blades.
    Intermediate
    RELEST Wind Gelcoat Transparent - I372-0002
    RELEST Wind Gelcoat Transparent is a viscoplastic, solvent-free polyaspartic coating with high tear propagation strength for use as an in-mould gelcoat. Suitable for making transparent, bubble-free and fast drying intermediate coats. RELEST Wind Gelcoat Transparent offers a pore-free surface after demoulding with very good UV stability allowing it to be topcoated without any additional working steps.
    Finish
    Devthane 378
    A high performance, two component, chemically cured, aliphatic urethane semi-gloss finish. *Please note this product is only available in North America.
    Primer
    RELEST Wind EP Process Coat - I355-0100
    RELEST Wind EP Process Coat is a two component, solvent free epoxy in-mould gel coat for wind turbine blade production.
    Primer
    Interdur 8805
    A two component, rapid recoat, fast curing solvent based inorganic zinc rich ethyl silicate primer. Conforms to SSPC Paint 20 Level 3. Available in ASTM D520, Type II zinc dust version as standard.
    1. 1

    Sorry, we couldn't find any results
    Fetching the data, please wait...