BACK TO PRODUCTS

Onshore Oil and Gas

Reliable Coating Solutions for Long-Lasting Performance
  • Extend service life with durable coatings.
  • Reduce unplanned shutdowns with corrosion protection.
  • Optimize efficiency in tough onshore environments.
     

EXPLORE CASE STUDIES

CASES

Durable Protection for a Landmark LNG Project

Filter by

Products

355 Product Found
My Filters
    Primer
    Devprime 1409
    A high solids, rust-inhibitive, interior-exterior alkyd primer for use on ferrous and non-ferrous metal including galvanized metal and aluminium. *Please note this product is only available in North America.
    Finish
    Intercryl 530 (Formerly Devcryl 1448)
    A premium quality, low VOC, direct to metal acrylic semi-gloss enamel for high traffic interior - exterior areas of commercial, institutional and industrial structures. *Please note this product is only available in North America.
    Other
    RELEST Wind Gelcoat - I372-7338
    RELEST Wind Gelcoat ca. RAL 7038, RA is a solvent free 2k viscoplastic, polyaspartic coating with excellent abrasion resistance. Suitable as part of a coating system for UV- and weather- resistance. Film thicknesses of approximately 200μm can be achieved in one step with optimal flow properties. RELEST Wind Gelcoat ca. RAL 7038, RA is characterised by its great adhesion to epoxy laminate.
    Primer-Finish
    Bar-Rust 231LV
    An ultra low VOC, high performance, multi-purpose, surface tolerant, two-component chemically-cured epoxy semi-gloss coating.
    Finish
    Devthane 379H
    A high performance, low VOC, two-component chemically-cured aliphatic urethane gloss finish. *Please note this product is only available in North America.
    Filler
    RELEST Wind Putty Contour Cartridge - I373-3715
    RELEST Wind Putty Contour Cartridge is a Solvent-free, highly viscous polyurethane putty for smoothing surface and contour irregularities. Its easy sanding and rapid cure properties offers increased productivity for further processing and recoating. RELEST Wind Putty Contour is ideally situated for mechanical application. It is supplied in a convenient 2-component cartridge for direct application of minimal quantities without weighing.
    Primer-Finish
    Interdur 8844
    A low VOC, two component high build, high solids, epoxy immersion coating. Designed to give long term protection in a single coat for immersion service situations. A winter curing agent is available to assist faster turn around times in cold conditions. CHINA ONLY
    Surface Pre-Treatment
    Devprep 88
    A concentrated water based cleaner low in odour, non-flammable and biodegradable. *Please note this product is only available in North America.
    Other
    Interkote MP
    Interkote MP is a single component mouldable putty, designed for efficient and cost-effective repair of damaged or compromised concrete and light weight cementitious (LWC) passive fire protection.
    Preconstruction Primer
    Interplate 937
    A two pack, heat resistant zinc silicate shop (pre-construction) primer providing good corrosion protection (even after heating up to 800°C (1472°F)), with minimum production of zinc salts. Suitable for high speed welding and cutting with excellent resistance to damage caused by welding, gas cutting and fairing thereby reducing secondary surface preparation requirements in comparison to typical zinc silicate products.
    Intermediate
    RELEST Wind Gelcoat Transparent - I372-0002
    RELEST Wind Gelcoat Transparent is a viscoplastic, solvent-free polyaspartic coating with high tear propagation strength for use as an in-mould gelcoat. Suitable for making transparent, bubble-free and fast drying intermediate coats. RELEST Wind Gelcoat Transparent offers a pore-free surface after demoulding with very good UV stability allowing it to be topcoated without any additional working steps.
    Finish
    Devthane 378
    A high performance, two component, chemically cured, aliphatic urethane semi-gloss finish. *Please note this product is only available in North America.
    Other
    Interseal 3377
    Interseal 3377 is designed to provide excellent short term protection against a wide range of contaminants such as dust, oil, grease, grinding debris, fly rust and coating application overspray whilst providing a degree of resistance to abrasion, grinding debris and scuffing.The dual protective and unique peelable properties of Interseal 3377 make it ideal for use in thosemarket areas where coated substrates require temporary protection against incidentalcontamination and damage, such as that experienced during transit or in a fabrication - assemblyconstruction process.Interseal 3377 can assist in providing a significant reduction in immediate and longer term coatingmaintenance costs whilst improving productivity during assembly and installation.
    Surface Tolerant
    Bar-Rust 235
    Bar-Rust 235 is a high performance, multi-purpose, surface tolerant, two-component chemically-cured epoxy semi-gloss coating.
    Finish
    Interfine 2080HS
    A fast-drying, high performance, high solids isocyanate free and tin free hybrid polysiloxane finish. Interfine 2080HS combines both acrylic and epoxy resin technology to deliver high durability with added flexibility and offers excellent gloss and colour retention when compared to conventional acrylic and polyurethane finishes.  Being isocyanate-free and tin free can help to support the sustainability and HSE objectives of the contract chain - Interfine 2080HS does not produce di-isocyanates during onsite hot-work.
    1. 1

    Sorry, we couldn't find any results
    Fetching the data, please wait...