BACK TO PRODUCTS

All Products

Filter by

Products

505 Product Found
My Filters
    Primer-Finish
    Interdur 8844
    A low VOC, two component high build, high solids, epoxy immersion coating. Designed to give long term protection in a single coat for immersion service situations. A winter curing agent is available to assist faster turn around times in cold conditions. CHINA ONLY
    Other
    RELEST Wind LEP ETU - I374-8735
    RELEST Wind LEP Easy To Use is a two-component solvent-free polyurethane coating for the M&R market which is especially designed for protecting the leading edge of rotor blades of wind energy plants from erosion damage caused by rain, sand, hail, dirt and other particles suspended in the air. The coating consists of an exceptionally fast, hard wearing, UV- and abrasion resistant polyurethane elastomer.
    Surface Pre-Treatment
    Devprep 88
    A concentrated water based cleaner low in odour, non-flammable and biodegradable. *Please note this product is only available in North America.
    Other
    Interkote MP
    Interkote MP is a single component mouldable putty, designed for efficient and cost-effective repair of damaged or compromised concrete and light weight cementitious (LWC) passive fire protection.
    Primer-Finish
    RELEST Wind Adhesion Promoter - I367-0080
    RELEST Wind Adhesion Promoter is a two component polyurethane material designed to ensure optimal adhesion for PVC, aluminium cast, CDC, PMAA and GRP based on epoxy or polyester. It is is especially suited for use in combination with wear protection coatings for rotor blades.
    Intermediate
    InterH2O 499S
    InterH2O 499S is a two component, fast drying water borne epoxy coating. It is suitable for use as a direct-to-metal primer or as an intermediate.
    Preconstruction Primer
    Interplate 937
    A two pack, heat resistant zinc silicate shop (pre-construction) primer providing good corrosion protection (even after heating up to 800°C (1472°F)), with minimum production of zinc salts. Suitable for high speed welding and cutting with excellent resistance to damage caused by welding, gas cutting and fairing thereby reducing secondary surface preparation requirements in comparison to typical zinc silicate products.
    Intermediate
    RELEST Wind Gelcoat Transparent - I372-0002
    RELEST Wind Gelcoat Transparent is a viscoplastic, solvent-free polyaspartic coating with high tear propagation strength for use as an in-mould gelcoat. Suitable for making transparent, bubble-free and fast drying intermediate coats. RELEST Wind Gelcoat Transparent offers a pore-free surface after demoulding with very good UV stability allowing it to be topcoated without any additional working steps.
    Finish
    Devthane 378
    A high performance, two component, chemically cured, aliphatic urethane semi-gloss finish. *Please note this product is only available in North America.
    Other
    Interseal 3377
    Interseal 3377 is designed to provide excellent short term protection against a wide range of contaminants such as dust, oil, grease, grinding debris, fly rust and coating application overspray whilst providing a degree of resistance to abrasion, grinding debris and scuffing.The dual protective and unique peelable properties of Interseal 3377 make it ideal for use in thosemarket areas where coated substrates require temporary protection against incidentalcontamination and damage, such as that experienced during transit or in a fabrication - assemblyconstruction process.Interseal 3377 can assist in providing a significant reduction in immediate and longer term coatingmaintenance costs whilst improving productivity during assembly and installation.
    Primer
    Interbuild 1072
    Interbuild 1072 is a low VOC, two component high build, high solids epoxy floor coating, reinforced with high aspect ratio glass flake. It has excellent chemical, abrasion and impact resistance. Can be applied directly in two coats or on approved primers depending on the conditions of the concrete substrate. Interbuild 1072 is designed to be used in high traffic areas.
    Surface Tolerant
    Bar-Rust 235
    Bar-Rust 235 is a high performance, multi-purpose, surface tolerant, two-component chemically-cured epoxy semi-gloss coating.
    Other
    Ceilcote 505BRAR Coroline System
    International PC - System
    Primer
    RELEST Wind EP Process Coat - I355-0100
    RELEST Wind EP Process Coat is a two component, solvent free epoxy in-mould gel coat for wind turbine blade production.
    Finish
    Interfine 2080HS
    A fast-drying, high performance, high solids isocyanate free and tin free hybrid polysiloxane finish. Interfine 2080HS combines both acrylic and epoxy resin technology to deliver high durability with added flexibility and offers excellent gloss and colour retention when compared to conventional acrylic and polyurethane finishes.  Being isocyanate-free and tin free can help to support the sustainability and HSE objectives of the contract chain - Interfine 2080HS does not produce di-isocyanates during onsite hot-work.
    1. 1

    Sorry, we couldn't find any results
    Fetching the data, please wait...